Browsing by Subject "DIAL"

Now showing 1 - 5 of 5

10 W-Average-Power Single-Frequency Ti:sapphire Laser with Tuning Agility – A Breakthrough in High-Resolution 3D Water-Vapor Measurement
(2018) Metzendorf, Simon; Wulfmeyer, Volker
The differential absorption lidar (DIAL) technique is well suited for measuring the humidity field of the atmosphere with high spatial and temporal resolution as well as accuracy. The water-vapor DIAL of the University of Hohenheim is a mobile, ground-based, scanning system. The DIAL methodology and the application in the Hohenheim-DIAL impose stringent requirements on the laser transmitter. In this thesis, a new laser transmitter was realized and employed. It is a pulsed, actively frequency-stabilized titanium-sapphire laser system, pumped with a Nd:YAG master-oscillator power-amplifier (MOPA) and alternately seeded by two diode lasers. As pump source, two commercially custom-made, diode-pumped, Q-switched, and frequency-doubled Nd:YAG lasers in MOPA architecture were employed. The relevant properties for pumping the Ti:sapphire laser were studied. The second Nd:YAG MOPA provides a considerably higher average output power (up to P = 63 W at 532 nm, or a pulse energy of up to E = 210 mJ at a repetition rate of f = 300 Hz) and an almost ideal top-hat beam profile. Thus, efficient end-pumping of the Ti:sapphire crystal was enabled without any optical damage. The components for injection seeding of the titanium-sapphire laser, making narrowband operation at two alternating frequencies (online and offline) possible, were substantially improved. Now, advanced commercial external-cavity diode lasers (ECDL) are applied. With an analog regulation signal of a wavelength meter, the frequency of an ECDL can be stabilized precisely to a defined value (standard deviation < 1 MHz). Optionally, the frequency can be tuned according to various mathematical functions. The online-offline-switching is accomplished with a fiber switch. The crosstalk is extraordinarily low (< -61 dB), the switching time sufficiently short (~ 1.5 ms), and the spatial overlap of the signals, due to the waveguide, almost perfect. The power of the seeders in front of the resonator is more than sufficient, 17-20 mW. The Ti:sapphire laser consists of a ring resonator with four mirrors in a bow-tie layout. With adequate components, the operation wavelength at 818 nm is pre-selected and unidirectional propagation is ensured. The laser crystal is installed in an in-house-manufactured cooling mount, of which two designs were utilized and compared. The gain-switched Ti:sapphire laser was developed to operate in a dynamically stable state of the thermal lens, which arises in the crystal at high powers. To this end, the resonator was theoretically analyzed beforehand and the focal length of the thermal lens measured. The implementation of a cylindrical lens compensates the stronger contraction of the eigenmode in the tangential plane. By these means, a stable operation with an average output power of P = 10 W (corresponding to E = 33.3 mJ at f = 300 Hz; pulse duration ~ 30 ns) was realized. With a modified configuration of the cylindrical lens a maximum output power of P_max = 11.8 W (E_max = 39.3 mJ) was achieved. These values are the highest which were obtained so far for a laser of this kind, i.e., a laser transmitter whose power originates from a single radiation source (without further amplification or conversion). The laser cavity is actively stabilized to the frequency of the seeder, following a Pound-Drever-Hall technique. This yields permanent single-frequency operation with very high frequency stability (standard deviation < 2 MHz) and a narrow linewidth (< 63 MHz). These results correspond to the resolution limit of the characterizing wavelength meter. Laser emission occurs in the fundamental transverse mode, TEM_00 (M² <= 1.06). The laser system of the Hohenheim-DIAL has been successfully operated on several field campaigns. Its robustness has been demonstrated, for instance, during an uninterrupted operation for over 30 hours and an overseas transport to the USA which the system endured without damage. This work presents a vertical pointing and two scanning water-vapor DIAL measurements, confirming a high resolution and accuracy. The vertical measurement was executed for the first time at 10 W laser operation. Furthermore, two special DIAL measurements are discussed: The measurements on a strongly backscattering target demonstrate a high spectral purity >= 99.97% of the laser transmitter. Finally, an atmospheric measurement with a tuning online wavelength shows the frequency-agility of the laser and allows to determine the water-vapor absorption line experimentally. The comparison with the spectrum of a database shows a very good agreement (~ 5-10 % deviation in the absorption cross sections absolute value).
A high-power laser transmitter for ground-based and airborne water-vapor measurements in the troposphere
(2009) Schiller, Max; Wulfmeyer, Volker
A gain-switched high-power single-frequency Ti:sapphire laser was developed. It is pumped with a frequency-doubled diode-pumped Nd:YAG laser. The laser fulfills the requirements for a transmitter of a water-vapor differential absorption lidar (DIAL), intended for accurate high temporally- and spatially-resolved measurements from the ground to the upper troposphere. The laser was developed using thermal, resonator-design, spectral, and pulse-evolution models. There were layouts assembled for operation at 935 nm and 820 nm optimized for airborne and groundbased measurements, respectively. A birefringent filter and an external-cavity diode laser as an injection seeder are controlling the spectral properties of the transmitter. With a frequency stability of < 60 MHz rms, an emission bandwidth of < 160 MHz, and a spectral purity of > 99.7 %, the total error from the laser properties is smaller than 5 % for water-vapor measurements in the troposphere. The laser beam profile is near-Gaussian with M2 < 2. The achieved laser power was 4.5 W at 935 nm and 7 W at 820 nm at repetition rate of 250 Hz. These values are the highest reported for a single-frequency Ti:sapphire laser. As a part of a ground-based water-vapor DIAL system, the transmitter was deployed during the measurement campaign COPS (Convective and Orographically-induces Precipitation Study). Comparisons with radiosondes confirmed a high precision of the acquired water-vapor day- and nighttime measurements.
Development of an eye-safe solid-state tunable laser transmitter around 1.45 my m based on Cr 4+:YAG crystal for lidar applications
(2008) Petrova-Mayor, Anna; Wulfmeyer, Volker
A gain switched tunable Cr4+:YAG laser was developed using a Q-switched flashlamp?pumped Nd:YAG pump laser at 10 Hz. A vacuum spatial filter (VSF) was designed in order to filter the ?hot spots? of the pump beam profile. As a result of applying the VSF, a nearly Gaussian-shaped beam profile was achieved which enabled safe pumping of the Cr4+:YAG crystal with pulse energies in excess of 100 mJ. An extensive experimental optimization of the efficiency of the wavelength converter was performed. A maximum output energy of ~7 mJ at 1430?1450 nm, corresponding to ~7% conversion efficiency (with regard to absorbed pump energy), and a pulse duration of 30?35 ns were obtained with a 25-cm-long stable resonator. Tunability in the range 1350?1500 nm and spectral linewidth of ~200G Hz were demonstrated using a 3-plate birefringent filter. The laser was multimode with a flat-top profile and sufficiently good M2~4. The performance and size of the laser are acceptable for use in a laboratory based non-scanning lidar system if a narrow-band birefringent filter is installed. In order to employ a scanning mobile lidar, high pulse frequency (>100 Hz) of the pump laser for the Cr4+:YAG laser is required. The tunability permits the improvement of the laser transmitter for water-vapor DIAL measurements at on-line wavelengths of approximately 1459 nm or 1484 nm if injection-seeding is applied.
Studies of soil-vegetation-atmosphere feedback processes with WRF on the convection permitting scale
(2017) Milovac, Josipa; Wulfmeyer, Volker
Land system models which can incorporate land-atmosphere and human-environment interactions are vital for reliable climate projections in heterogeneous agricultural landscapes. At resolutions fine enough to resolve detailed land use, models need a sophisticated representation of planetary boundary layer (PBL) and land surface processes in order to predict changes in key quantities like precipitation or temperatures. Assessment of turbulence schemes and land surface models (LSM) is fundamental therefore not only to advance model development, but also to understand important phenomena like feedbacks within the soil-vegetation-atmosphere (SVA) continuum. Up until now however, a lack of appropriate observations has impeded any comprehensive assessments. Here, through comparisons with so far unique profile measurements, the study investigates the impact of using different PBL schemes and LSMs, and explores how SVA feedbacks are simulated by the model. Using the Weather Research and Forecasting (WRF) model, a six member ensemble was run, at a convection permitting resolution, with varying combinations of LSMs (NOAH and NOAH-MP) and PBL schemes (two local and two non-local approaches). The analysis was performed for two case studies – a dry and a convective weather situation – in three different locations in Germany. During the dry case, key convective PBL (CBL) features were analysed, and the simulations were compared with high resolution water vapour differential absorption lidar measurements. For the convective case, the focus was on exploring the model representation of the pre-convective environment and the ensuing convection and precipitation. In both cases, the nature of the simulated SVA feedback processes was assessed through an innovative “mixing diagram” approach. Results show that the nonlocal PBL schemes produce a drier and higher CBL than the local schemes. These results are sensitive to parameters calculated in the surface layer schemes, which are themselves often paired with PBL schemes. Furthermore, the NOAH‑MP LSM produces drier atmospheric conditions than NOAH, with a difference in mixing ratio profiles ranging up to 1.4 gkg-1. These variations are more pronounced in the upper CBL than close to the ground. The mixing diagrams indicate that these deviations are mainly related to entrainment fluxes. In the dry case, NOAH-MP’s dry air entrainment is up to 6 times higher than with NOAH, while in the convective case the difference is not as pronounced (up to 1.5 higher with NOAH-MP). This suggests that the difference in the simulation of the CBL between the two LSMs is strongly linked to the surface energy partitioning – the higher the Bowen ratio, the greater the difference between the LSMs. Thus, WRF appears to be more sensitive to the choice of LSM at higher Bowen ratios. NOAH and NOAH-MP exhibit marked differences in representing atmospheric variables such as moisture. Those differences are not constrained to the lower atmosphere close to the land surface, but extended to the lower troposphere. The variations in free tropospheric moisture between the LSMs strongly affects the nature of the simulated convection, and associated precipitation. The degree of sensitivity of the spatial variability and amount of the precipitation with respect to the selection of LSM and PBL scheme shows a strong dependence on the analysed region. A distinct finding of this thesis is the greater sensitivity of WRF with respect to the PBL development to the selection of the LSM, than to the PBL scheme. Furthermore, the impact of this sensitivity is not constrained to the lower CBL, but extends up to the interfacial layer and the lower troposphere - for both dry and convective weather conditions. On the other hand, it is clear that the simulated coupling strength between the land surface and atmosphere is very sensitive to the surface Bowen ratio. The synergies between high resolution measurements and model simulations, with an advanced representation of the land surface processes, will facilitate not only further development of parameterization schemes, but also an improvement in our understanding of land-atmosphere interactions.
Theoretical analysis and design of high-performance frequency converters for LIDAR systems
(2009) Wagner, Gerd; Wulfmeyer, Volker
Frequency converters based on parametric and nonparametric frequency conversion are analyzed with respect to the specifications for high-average power water-vapor DIAL transmitters (DIAL: Differential Absorption LIDAR; LIDAR: Light Detection and Ranging). A Ti:Sapphire laser was selected as a suitable frequency converter to fulfill simultaneously all the requirements in the wavelength range of 935 nm and 820 nm. As thermal effects have a decisive influence on the overall performance and laser resonator design, they were simulated on Ti:Sapphire laser crystals in detail for different crystals, pump, and cooling configurations using finite element analysis (FEA). The performance and spectral properties of the Ti:Sapphire laser transmitter were modeled with a rate-equation approach for stable and unstable resonators. First theoretical results of an end-pumped Ti:Sapphire laser based on an optimized, asymmetric confocal unstable ring resonator design are presented. The obtained results can especially be used for the further development of a Ti:Sapphire laser to serve as a demonstrator for a future space-borne DIAL system transmitter according to the WALES (Water Vapor Lidar Experiment in Space) specifications. Furthermore, the adaptation of the developed theory modules to other lasing materials and configurations is straightforward.