Browsing by Subject "Titan-Saphir-Laser"

Now showing 1 - 3 of 3

10 W-Average-Power Single-Frequency Ti:sapphire Laser with Tuning Agility – A Breakthrough in High-Resolution 3D Water-Vapor Measurement
(2018) Metzendorf, Simon; Wulfmeyer, Volker
The differential absorption lidar (DIAL) technique is well suited for measuring the humidity field of the atmosphere with high spatial and temporal resolution as well as accuracy. The water-vapor DIAL of the University of Hohenheim is a mobile, ground-based, scanning system. The DIAL methodology and the application in the Hohenheim-DIAL impose stringent requirements on the laser transmitter. In this thesis, a new laser transmitter was realized and employed. It is a pulsed, actively frequency-stabilized titanium-sapphire laser system, pumped with a Nd:YAG master-oscillator power-amplifier (MOPA) and alternately seeded by two diode lasers. As pump source, two commercially custom-made, diode-pumped, Q-switched, and frequency-doubled Nd:YAG lasers in MOPA architecture were employed. The relevant properties for pumping the Ti:sapphire laser were studied. The second Nd:YAG MOPA provides a considerably higher average output power (up to P = 63 W at 532 nm, or a pulse energy of up to E = 210 mJ at a repetition rate of f = 300 Hz) and an almost ideal top-hat beam profile. Thus, efficient end-pumping of the Ti:sapphire crystal was enabled without any optical damage. The components for injection seeding of the titanium-sapphire laser, making narrowband operation at two alternating frequencies (online and offline) possible, were substantially improved. Now, advanced commercial external-cavity diode lasers (ECDL) are applied. With an analog regulation signal of a wavelength meter, the frequency of an ECDL can be stabilized precisely to a defined value (standard deviation < 1 MHz). Optionally, the frequency can be tuned according to various mathematical functions. The online-offline-switching is accomplished with a fiber switch. The crosstalk is extraordinarily low (< -61 dB), the switching time sufficiently short (~ 1.5 ms), and the spatial overlap of the signals, due to the waveguide, almost perfect. The power of the seeders in front of the resonator is more than sufficient, 17-20 mW. The Ti:sapphire laser consists of a ring resonator with four mirrors in a bow-tie layout. With adequate components, the operation wavelength at 818 nm is pre-selected and unidirectional propagation is ensured. The laser crystal is installed in an in-house-manufactured cooling mount, of which two designs were utilized and compared. The gain-switched Ti:sapphire laser was developed to operate in a dynamically stable state of the thermal lens, which arises in the crystal at high powers. To this end, the resonator was theoretically analyzed beforehand and the focal length of the thermal lens measured. The implementation of a cylindrical lens compensates the stronger contraction of the eigenmode in the tangential plane. By these means, a stable operation with an average output power of P = 10 W (corresponding to E = 33.3 mJ at f = 300 Hz; pulse duration ~ 30 ns) was realized. With a modified configuration of the cylindrical lens a maximum output power of P_max = 11.8 W (E_max = 39.3 mJ) was achieved. These values are the highest which were obtained so far for a laser of this kind, i.e., a laser transmitter whose power originates from a single radiation source (without further amplification or conversion). The laser cavity is actively stabilized to the frequency of the seeder, following a Pound-Drever-Hall technique. This yields permanent single-frequency operation with very high frequency stability (standard deviation < 2 MHz) and a narrow linewidth (< 63 MHz). These results correspond to the resolution limit of the characterizing wavelength meter. Laser emission occurs in the fundamental transverse mode, TEM_00 (M² <= 1.06). The laser system of the Hohenheim-DIAL has been successfully operated on several field campaigns. Its robustness has been demonstrated, for instance, during an uninterrupted operation for over 30 hours and an overseas transport to the USA which the system endured without damage. This work presents a vertical pointing and two scanning water-vapor DIAL measurements, confirming a high resolution and accuracy. The vertical measurement was executed for the first time at 10 W laser operation. Furthermore, two special DIAL measurements are discussed: The measurements on a strongly backscattering target demonstrate a high spectral purity >= 99.97% of the laser transmitter. Finally, an atmospheric measurement with a tuning online wavelength shows the frequency-agility of the laser and allows to determine the water-vapor absorption line experimentally. The comparison with the spectrum of a database shows a very good agreement (~ 5-10 % deviation in the absorption cross sections absolute value).
A high-power laser transmitter for ground-based and airborne water-vapor measurements in the troposphere
(2009) Schiller, Max; Wulfmeyer, Volker
A gain-switched high-power single-frequency Ti:sapphire laser was developed. It is pumped with a frequency-doubled diode-pumped Nd:YAG laser. The laser fulfills the requirements for a transmitter of a water-vapor differential absorption lidar (DIAL), intended for accurate high temporally- and spatially-resolved measurements from the ground to the upper troposphere. The laser was developed using thermal, resonator-design, spectral, and pulse-evolution models. There were layouts assembled for operation at 935 nm and 820 nm optimized for airborne and groundbased measurements, respectively. A birefringent filter and an external-cavity diode laser as an injection seeder are controlling the spectral properties of the transmitter. With a frequency stability of < 60 MHz rms, an emission bandwidth of < 160 MHz, and a spectral purity of > 99.7 %, the total error from the laser properties is smaller than 5 % for water-vapor measurements in the troposphere. The laser beam profile is near-Gaussian with M2 < 2. The achieved laser power was 4.5 W at 935 nm and 7 W at 820 nm at repetition rate of 250 Hz. These values are the highest reported for a single-frequency Ti:sapphire laser. As a part of a ground-based water-vapor DIAL system, the transmitter was deployed during the measurement campaign COPS (Convective and Orographically-induces Precipitation Study). Comparisons with radiosondes confirmed a high precision of the acquired water-vapor day- and nighttime measurements.
Theoretical analysis and design of high-performance frequency converters for LIDAR systems
(2009) Wagner, Gerd; Wulfmeyer, Volker
Frequency converters based on parametric and nonparametric frequency conversion are analyzed with respect to the specifications for high-average power water-vapor DIAL transmitters (DIAL: Differential Absorption LIDAR; LIDAR: Light Detection and Ranging). A Ti:Sapphire laser was selected as a suitable frequency converter to fulfill simultaneously all the requirements in the wavelength range of 935 nm and 820 nm. As thermal effects have a decisive influence on the overall performance and laser resonator design, they were simulated on Ti:Sapphire laser crystals in detail for different crystals, pump, and cooling configurations using finite element analysis (FEA). The performance and spectral properties of the Ti:Sapphire laser transmitter were modeled with a rate-equation approach for stable and unstable resonators. First theoretical results of an end-pumped Ti:Sapphire laser based on an optimized, asymmetric confocal unstable ring resonator design are presented. The obtained results can especially be used for the further development of a Ti:Sapphire laser to serve as a demonstrator for a future space-borne DIAL system transmitter according to the WALES (Water Vapor Lidar Experiment in Space) specifications. Furthermore, the adaptation of the developed theory modules to other lasing materials and configurations is straightforward.