Browsing by Person "Gibis, Monika"

Now showing 1 - 13 of 13

Analysis of aging-related changes and influencing factors on the metabolome of beef
(2023) Bischof, Greta; Gibis, Monika
Aging of beef is necessary to improve its flavor and tenderness. There are two most common aging types, dry-aging and wet-aging. Dry-aged beef is often associated with a higher eating quality than wet-aged beef. The term “dry-aged beef” is not legally defined, so authentication methods are needed to protect the consumers from food fraud. During beef aging, the metabolome of beef changes due to the postmortem metabolism. This dissertation focuses on the aging method as a postmortem process and the resulting changes in the metabolome. As a hypothesis of this study, it was postulated that the detection of these metabolic changes due to aging of beef is feasible by 1H NMR spectroscopy and based on these measurements the evaluation of an authentication model for the aging method of beef is possible. In order to test this hypothesis, a sample preparation and measurement method was developed and based on this, potential influencing factors such as sampling position in muscle, breed and sex were investigated on the metabolome of fresh and aged beef. In the first part of this thesis, the sample preparation and the 1H NMR measurement method were developed. In the sample preparation, the polar fraction of the metabolome was extracted from 200 mg of beef, allowing 24 samples to be prepared in parallel. The sample preparation and the measurement method were validated, and the first aged beef samples were analyzed to check if the aging-related changes in the metabolome could be detected by this method. In the second part of this thesis, the sampling position in the muscle were analyzed for changes or differences in the metabolome due to its location in the muscle. The results showed that the metabolome changes along the length of the M. longissimus thoracis et lumborum, but the influence of the aging type and aging time was more pronounced in the metabolome of beef. The comparison of the surface and the inner part of wet-aged and dry-aged beef showed that the metabolome of dry-aged beef differed greatly between the surface and the inner part, despite the exclusion of the moisture content by freeze-drying and the low microbial load. There were only slight differences between the surface and the inner part for wet-aged beef, which could be due to the influence of microbiota and their metabolites. Therefore, the sampling location in the M. longissimus thoracis et lumborum was determined as precisely as possible for the further studies. The muscles were cut into ten pieces from cranial to caudal and dry-aged or wet-aged for 0, 7, 14, 21, and 28 days, in duplicates. The third part of this thesis focuses on the potential influencing factors such as breed and sex of the animals. Fresh and aged beef samples from three cattle types (heifer, cow, and young bull) and two different breeds (‘Fleckvieh’ and ‘Schwarzbunt’) were analyzed by targeted and non-targeted 1H NMR spectroscopy. Both factors were shown to influence the metabolome of fresh and aged beef. Therefore, these factors had to be included in the authentication model based on both targeted and non-targeted model. The calculation of the authentication model was the main part of this thesis and showed a good prediction of cattle type, breed, aging time and aging type of beef. The authentication model was based on the combination of multiple models of PLS-R and PLS-DA. The model for predicting the cattle type showed an accuracy of 99 %, and the models for predicting the breed depending on the cattle type showed an accuracy of 100 %. Aging time could be predicted with an error of 2.28 days. The statistical models for aging type were separated by aging time based on the determination of aging time. The model for predicting the aging type of 28-day aged samples had an accuracy of 99 %. The other statistical models for predicting aging type were additionally separated by cattle type and breed, and their accuracy ranged from 90 % to 100 %. In conclusion, an authentication model to determine the cattle type, breed, aging time and aging type of beef was developed in this dissertation. Therefore, it is possible to authenticate beef samples using a single 1H NMR spectrum. In future studies, it would be useful to extend this authentication model to other samples of other breeds and influencing factors.
Characterization of the aroma profile of food smoke at controllable pyrolysis temperatures
(2023) Rigling, Marina; Höckmeier, Laura; Leible, Malte; Herrmann, Kurt; Gibis, Monika; Weiss, Jochen; Zhang, Yanyan
Smoking is used to give food its typical aroma and to obtain the desired techno-functional properties of the product. To gain a deeper knowledge of the whole process of food smoking, a controllable smoking process was developed, and the influence of wood pyrolysis temperature (150–900 °C) on the volatile compounds in the smoking chamber atmosphere was investigated. The aroma profile of smoke was decoded by headspace solid-phase microextraction-gas chromatography-mass spectrometry (HS-SPME-GC-MS). Subsequently, the correlations in the most important substance classes, as well as in individual target components, were investigated by the Pearson test. Phenols and lactones showed an increase over the entire applied temperature range (rT = 0.94 and rT = 0.90), whereas furans and carbonyls showed no strict temperature dependence (rT < 0.6). Investigations on single aroma compounds showed that not all compounds of one substance class showed the same behavior, e.g., guaiacol showed no significant increase over the applied pyrolysis temperature, whereas syringol and hydoxyacetone showed a plateau after 450 °C, and phenol and cyclotene increased linear over the applied temperature range. These findings will help to better understand the production of aroma-active compounds during smoke generation in order to meet consumers preferences.
Effect of frozen to fresh meat ratio in minced pork on its quality
(2023) Tomasevic, Igor; Witte, Franziska; Kühling, Rike Elisabeth; Berger, Lisa M.; Gibis, Monika; Weiss, Jochen; Röser, Anja; Upmann, Matthias; Joeres, Eike; Juadjur, Andreas; Bindrich, Ute; Heinz, Volker; Terjung, Nino
The meat industry is typically using a mixture of fresh and frozen meat batters for minced meat production. Our goal was to find the exact threshold for fresh to frozen meat ratio capable of controlling the meat temperature during processing, but without having an adverse effect on the sensory quality of minced pork. To achieve this, the percentage of frozen meat used for the minced pork production was increased from 0% (control) to 50% (maximum) in 10% increments. To keep the minced meat temperature in control and make the processing resistant to fat smearing, the addition of 30% of frozen meat to the meat batter is sufficient. The soluble protein content, instrumental cutting force, and the sensory perceived firmness, juiciness, and inner cohesion were not affected by the addition of frozen meat. However, it has contributed to a significant increase of the drip loss and the amount of non-intact cells (ANIC). With the addition of frozen meat into the minced pork, the compliance to ANIC regulation by the German regulatory authorities is technologically (practically) almost impossible.
Effect of storage temperature on volatile marker compounds in cured loins fermented with Staphylococcus carnosus by brine injection
(2020) Bosse, Ramona; Wirth, Melanie; Weiss, Jochen; Gibis, Monika
In this study, the influence of low (5 °C), intermediate (15 °C) and high (25 °C) storage temperatures on the profile of volatile compounds of North European cured loins fermented with Staphylococcus carnosus strains was investigated. In this context, proteolytic activity, bacterial growth, key volatile compounds and sensory attributes were studied. In conclusion, storage temperature significantly affected the volatile marker compounds. A multiple regression indicated significant effects of seven volatile compounds (acetophenone, benzaldehyde, butanone, 3-methylbutanal, 1-octen-3-ol, nonanal and pentanone) on the overall odor (R2 = 95.9%) and overall flavor (R2 = 81.1%). The sum of the marker volatiles aldehydes, ketones and alcohol increased with rising temperatures and the highest amounts of the odor active 3-methylbutanal up to 155 and 166 ng/g meat were detected in high temperature-stored loins. Moreover, the addition of S. carnosus strain LTH 3838 showed maximum effect at 5 °C-storage temperature in comparison to the control.
Effects of fingerroot (Boesenbergia pandurata) oil on microflora as an antimicrobial agent and on the formation of heterocyclic amines in fried meatballs
(2024) Soikam, Panida; Rachtanapun, Chitsiri; Suriyarak, Sarisa; Weiss, Jochen; Gibis, Monika
This study aimed to determine the antibacterial activity of the essential oil of fingerroot (Boesenbergia pandurata) (EOF) as a natural preservative in ground meat and its effect on the formation of heterocyclic amines (HAs) in pan-fried meatballs. EOF was applied either by adding it to ground pork or marinating pork in it before grinding. In addition, the antibacterial activity of EOF was tested. Aerobic mesophilic total viable count (TVC), lactic acid bacteria (LAB), and Enterobacteriaceae bacteria were monitored. The results show that EOF exhibited strong antibacterial activity when added at concentrations of 1.0 and 2.5 wt%. Antimicrobial activity against TVC, LAB, and especially Enterobacteriaceae bacteria was observed at all EOF concentrations (0.25, 0.5, 1.0, and 2.5 wt%). A 2.5% concentration of EOF applied by marinating trimmings can extend the shelf-life of ground pork to 18 days, while 2.5% EOF applied via addition can extend the shelf-life to 15 days, compared with 3 days for the control sample. After frying the meatballs, the inhibitory effect on the formation of heterocyclic amines was only significant for MeIQx with the highest addition of EOF (2.5 wt%). Significant increases in the concentrations of all other HAs were determined by adding EOF (2.5 wt%).
Improving the colloidal stability of pectin–phycocyanin complexes by increasing the mixing ratio
(2024) Buecker, Stephan; Gibis, Monika; Bartmann, Laura; Bussler, Sara; Weiss, Jochen
In the food industry, the phycobiliprotein phycocyanin acts as a color pigment or the functional part of the superfood “Spirulina.” It is industrially extracted from Arthrospira platensis. Current scientific research is focusing on finding complex partners with the potential to stabilize phycocyanin against its sensitivity toward heating and pH changes. Less attention is paid to the factors that influence complexation. This study focuses on the mixing ratio of phycocyanin with pectin. Phycocyanin concentration was fixed, and the mixing ratios ranged from 0.67 to 2.50 (pectin:phycocyanin). All samples were analyzed for their color, size, microscopic structure, zeta potential, and sedimentation stability before and after heating at 85°C. It was found that increasing the pectin content fostered the initial interactions with the protein and chromophore, resulting in a color shift from blue to turquoise. The size of the complexes decreased from several micrometers to nanometers with increasing pectin concentration. Those smaller complexes that were formed at a mixing ratio of 2.5 showed a higher colloidal stability over a period of ∼2 days. It is suggested that at a low mixing ratio (0.67), phycocyanin cannot be completely entrapped within the complexes and attaches to the complex surface as well. This results in aggregation and precipitation of the complexes upon heating. With increasing aggregation and consequently size as well as density of the complexes, sedimentation was accelerated.
Influence of finely chopped meat addition on quality parameters of minced meat
(2022) Witte, Franziska; Sawas, Erik; Berger, Lisa M.; Gibis, Monika; Weiss, Jochen; Röser, Anja; Upmann, Matthias; Joeres, Eike; Juadjur, Andreas; Bindrich, Ute; Heinz, Volker; Terjung, Nino
Larger processing equipment to produce minced meat could affect its structure due to intensive processing and a high energy intake in the meat mass. To assess if this would result in alterations in the minced meat quality, finely chopped meat (FCM) was added in different concentrations (15, 30, 45, 60, 75, 90, and 100%) to minced meat and quality parameters were analyzed. FCM was used to simulate different intensity of an unintended destruction of meat cells due to various processes. The amount of non-intact cells (ANIC) was determined histologically and furthermore, soluble protein content, water holding capacity, mechanical and sensory texture, and scanning electron and confocal laser scanning microscopy was applied to analyze the meat structure and quality. ANIC indicated that even adding 15% FCM was statistically (p < 0.05) distinguishable from 100% minced meat and 30% FCM had already 50 Vol.-% ANIC. In contrast, the addition of 15% or 30% FCM did not result in significant differences in drip loss of raw and cooked meat as well as mechanical and sensory texture analysis. This study showed that intensive processing might be detectable via ANIC, but that the minced meat quality was not affected.
Influence of muscle type and microstructure on iridescence in cooked, cured pork meat products
(2021) Ruedt, Chiara; Gibis, Monika; Weiss, Jochen
Microstructural factors associated with surface iridescence in cooked, cured pork products were investigated. Meat iridescence is a commonly observed physical phenomenon in raw meat and meat products that consist of intact mus- cle tissue. Since the purchase decision of consumers is mainly driven by the first impression of meat color and appearance, products showing colorful iri- descence may be rejected. Four different muscles (RF: M. rectus femoris, BF: M. biceps femoris, ST: M. semitendinosus, and LD: M. longissimus thoracis et lum- borum) were brine-injected, cooked, sliced, and iridescence was evaluated by digital image analysis and sensory analysis. Sarcomere lengths, fiber diameters, and surface microstructure were analyzed in iridescent and noniridescent sec- tions. Highest iridescence extent by image analysis was found in LD (37.3 ± 16.4%), and highest overall iridescence score (extent and intensity, 6.11 ± 1.78) was observed in BF. Sarcomere lengths did not differ significantly between iridescent (1.05 ± 0.09 µm LD) and noniridescent areas (1.08 ± 0.94 µm LD) within mus- cles (p > 0.05). Iridescent sections showed smooth and ordered surface structures with cross-sectioned myofibers, whereas in noniridescent sections, surfaces were more unstructured and myofibers obliquely cut. The results of the study indicate that the sarcomere length and fiber diameters may thus be only of minor impor- tance for the explanation of meat iridescence in cooked meat products and are rather related to multiple scattering and absorption effects on smaller structural entities such as the myofilament lattice or larger entities such as fiber bundles. Practical application: Iridescence can be a problem for the meat industry due to consumers concerns about green-iridescent colors in meat. The underlying mechanisms and structures have not yet been fully clarified, and thus no prac- tical solutions to eliminate iridescence have been found so far. This research presents new insights into the structural attributes that are interrelated with meat iridescence and shows that iridescence is rather influenced by cutting angle of muscle fibers and surface homogeneity than by muscle fiber diameters or sar- comere lengths. This should be considered by the industry when seeking for ways to reduce the potential problem of iridescence
Influence of processing steps on structural, functional, and quality properties of beef hamburgers
(2022) Berger, Lisa M.; Witte, Franziska; Terjung, Nino; Weiss, Jochen; Gibis, Monika
In hamburger manufacturing, meat is subjected to four main processing steps (pre-grinding, mixing, grinding, and forming), whereby muscle fibers are disintegrated. In this study, the influence of these process steps was characterized by structural (amount of non-intact cells (ANIC), CLS-Microscopy), functional (drip loss) and qualitative (soluble protein content, lactate dehydrogenase (LDH) activity, myoglobin content (Mb)) parameters of the meat. Therefore, meat samples were analyzed after each process step. Histological analyses revealed an increased ANIC with progressive processing. Thereby, the first and second grinding steps caused the strongest increases (factors 2.43 and 2.69). Comparable results were found in the relative LDH activity (factor 2.20 and 1.62) and the Mb concentration (factor 2.24 and 1.33) of the extracted meat solution. The findings suggest that the disintegration of the meat structure increases with progressive processing, causing more vulnerable structures which result in increased leakage of intramuscular substances. Further, the type of stress acting on the meat determines the extent of the changes. The presented findings enable manufacturers to precisely adjust their process towards more gentle production parameters and thus, to meet the legal regulations.
Influence of transport distance, animal weight, and muscle position on the quality factors of meat of young bulls during the summer months
(2024) Poveda-Arteaga, Alejandro; Bobe, Alexander; Krell, Johannes; Heinz, Volker; Terjung, Nino; Tomasevic, Igor; Gibis, Monika
This study investigated the potential effects of transport distance, animal weight, and muscle position on meat quality in young bulls under commercial conditions across four slaughtering weeks during the summer months (May to September). Data on transport distance, lairage time, and ambient temperature during slaughtering days were collected from 80 young bulls from North German farms. Meat quality parameters, including pH, temperature, and meat color were also recorded at several post-mortem times from two different carcass locations (shoulder clod and silverside). Meat texture was evaluated both by sensory and instrumental analysis, and their values were compared to find possible correlations between them. All of the aforementioned main factors (transport distance, animal weight, and muscle position), as well as the interaction between animal weight and transport distance, significantly influenced (p < 0.01) meat quality traits. The results of the assessment of the meat texture from the cooked meat patties suggested that silverside cuts were consistently harder than shoulder clod cuts, despite having lower pH48 values.
Intrinsic and extrinsic factors affecting the color of fresh beef meat - comprehensive review
(2023) Poveda-Arteaga, Alejandro; Krell, Johannes; Gibis, Monika; Heinz, Volker; Terjung, Nino; Tomasevic, Igor
Meat color research from the last two decades suggests that a combination of different intrinsic (ultimate pH, age of the animals, muscle position, breed, slaughter weight, and sex) and extrinsic factors (production systems and feeding, pre-mortem stress, slaughter season, and chilling rates) might have a deep impact in the color of beef muscle and influence consumers’ acceptance of fresh meat. Ultimate pH and muscle position were perceived as the most determinant intrinsic factors, whereas production systems, feeding, and ante-mortem stress were the extrinsic factors that more strongly influenced beef color attributes. From an industrial perspective, the extrinsic factors can be improved through the technological process at a higher ratio than the intrinsic ones. This review aims to evaluate the effect of each of those factors on myoglobin oxidation and beef color traits from a comprehensive standpoint. All the information discussed in this manuscript focuses on an industrial environment and offers possible solutions and recommendations for the global meat industry.
Meat color and iridescence: Origin, analysis, and approaches to modulation
(2023) Ruedt, Chiara; Gibis, Monika; Weiss, Jochen
Meat color is an important aspect for the meat industry since it strongly determines the consumers’ perception of product quality and thereby significantly influences the purchase decision. Emergence of new vegan meat analogs has renewed interest in the fundamental aspects of meat color in order to replicate it. The appearance of meat is based on a complex interplay between the pigment‐based meat color from myoglobin and its chemical forms and light scattering from the muscle's microstructure. While myoglobin biochemistry and pigment‐based meat color have been extensively studied, research on the physicochemical contribution of light scattering to meat color and the special case of structural colors causing meat iridescence has received only little attention. Former review articles focused mostly on the biochemical or physical mechanisms rather than the interplay between them, in particular the role that structural colors play. While from an economic point of view, meat iridescence might be considered negligible, an enhanced understanding of the underlying mechanisms and the interactions of light with meat microstructures can improve our overall understanding of meat color. Therefore, this review discusses both biochemical and physicochemical aspects of meat color including the origin of structural colors, highlights new color measurement methodologies suitable to investigate color phenomena such as meat iridescence, and finally presents approaches to modulate meat color in terms of base composition, additives, and processing.
Variations in the metabolome of unaged and aged beef from black-and-white cows and heifers by 1H NMR spectroscopy
(2023) Bischof, Greta; Januschewski, Edwin; Witte, Franziska; Terjung, Nino; Heinz, Volker; Juadjur, Andreas; Gibis, Monika
(1) Background: The selection of raw material and the postmortem processing of beef influence its quality, such as taste. In this study, the metabolome of beef from cows and heifers is examined for differences during aging. (2) Methods: Thirty strip loins from eight heifers and seven cows (breed code: 01–SBT) were cut into ten pieces and aged for 0, 7, 14, 21 and 28 days. Samples from the left strip loins were wet-aged in vacuum, while samples from right strip loins were dry-aged at 2 °C and 75% relative humidity. The beef samples were extracted with methanol–chloroform–water, and the polar fraction was used for 1H NMR analysis. (3) Results: The PCA and OPLS-DA showed that the metabolome of cows and heifers varied. Eight metabolites revealed significant differences (p < 0.05) in the samples from cows and heifers. The aging time and aging type of beef also affected the metabolome. Twenty-eight and 12 metabolites differed significantly (p < 0.05) with aging time and aging type, respectively. (4) Conclusions: The variations between cows and heifers and aging time affect the metabolome of beef. By comparison, the influence of aging type is present but less pronounced.